How to Clean a Wind Machine Fan

Many people generally don’t consider cleaning a wind machine fan. However, cleaning is vital to remove gathered dust and debris. If you don’t know how to clean it, keep reading this article to know how to clean a wind machine fan.

Methods to clean a wind machine fan

The cleaning of a wind machine fan often depends on how much dirt is accumulated on it. If your fan is new, it probably doesn’t have a lot of grime and dirt to clean. But if a fan is old, it may have a lot of dirt on its surface.

Here are two methods to keep your wind machine fan clean:

Use a Damp Cloth For Cleaning

First, you need to disassemble a fan after checking the user manual or on the company’s website. It makes it easier to clean its surface. After that, follow the given steps for cleaning:

• Unplug and turn off the wind machine fan:  Avoid cleaning it inside the house because you can wind up strewing particles there. The ideal location to use is the garage.
• Keep the fan on a flat surface:  Remove each screw, including the knob screws, with a screwdriver. Your wind machine fan can have a few unseen screws because the models vary.
• To see the blades, separate the grills:  The blades should be cleaned with a moist piece of cloth. You can dampen the cloth by soaking it in soapy water first, followed by clean water.
• Make sure the blades are thoroughly clean by wiping them: Avoid touching the fan’s motor.
• Let it air dry

Carefully assemble everything in the correct position after the blades have dried. Check the manual or the manufacturer’s website if you aren’t sure where something belongs.

If your wind machine cannot be disassembled, you can spray compressed air into the blades of the device. There will be no more dust or grime.

Use a Vacuum and Cleaning Solution

This method works well on equipment like blower fans and others that have a lot of buildups and haven’t been cleaned in a while.

Cleaning Supplies You Need

• Cleaning solution
• Vacuum
• Warm soapy water
• Screwdriver
• A toothbrush
• A clean piece of cloth
• Paper towels

1. Prioritize safety

The machine’s power supply should be taken out and unplugged from the outlet. While you’re about it, look for any exposed cables. You do not want them to be exposed to water or cause future accidents. If it is powered by batteries, take them out.

2. Take the Wind Machine Fan and Disassemble It

Unscrew the screws holding the housing in place, then set the wind machine fan on a solid flat surface. Remove any clips that may be present on some models. In some instances, a large nut secures the motor’s rear casing.

Also Read: How to Remove Caulk From Wall

Remove the blade first. Carefully remove each blade by turning the blade cover counterclockwise on the motor. Place it in warm, soapy water after that. At this point, it will be able to take the fan’s back off. Make sure to save all the screws safely so you can recall them later.

3. Use the Vacuum

Vacuum all the exposed components now that the fan has been revealed. You must not omit this step if you reside in a dusty environment. This step is not necessary if the area is not dusty. Compressed air is an alternative to employing a vacuum.

4. Clean With Cleaning Solution

If you don’t have a cleaning solution, fill a spray bottle with two tablespoons of dishwashing soap. To create a cleaning solution, top it off with around three glasses of water and shake vigorously. Use dishwashing soap with grease-cutting qualities for improved results.

It is not necessary to use a spray bottle; you can combine everything in a bowl instead. Take a clean cloth and dip it into the basin containing the mixture once you have your solution ready. Rinse out all the extra water, then start cleaning the blades.

Spray a tiny bit of the cleaning solution on the blades if you’re using a spray bottle, then scrub with a piece of cloth. Continue doing this until all of the blades are covered. Make sure water doesn’t get on the fan’s motor.

5. Clean the Given Cap

It’s time to clean the cap you cleaned in warm, soapy water. Additionally, you can clean whetstones and softball bats with this technique.

Make sure you purchase the proper brush; an old toothbrush is preferable to abrasive brushes designed for cleaning thermocouple water heaters. Use an old toothbrush to scrub the cap clean. Make sure to clean all the dirt and grime that has accumulated in the crevices.

6. Dry All the Parts

Dry each component of the fan with paper towels. Make careful to be really meticulous and not leave any pieces out. Additionally, leave everything exposed to sunlight and wind for around 30 minutes so it can dry completely.

7. Put the Fan back together

Lastly, you have to assemble the fan using the user manual or instructions given on the company’s website. you took out of the fan should be the first component you put back in.

This is how to clean wind machine fan with ease. You can use these two methods whenever you feel the need to clean your wind machine fan.